This unit describes the performance outcomes required to inspect motorcycle frames, determine and carry out required repairs, and then align the frames and their components. It involves preparing for the task, inspecting, measuring, repairing and aligning motorcycle frames, and completing workplace processes and documentation.
It applies to those working in the motorcycle service and repair industry. It includes all types of motorcycle frames, including those with side cars and carrying compartments.
No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)
Evidence Required
List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements
Elements describe the essential outcomes.
Performance Criteria
Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.
1. Prepare to inspect and measure motorcycle frame
1.1 Job requirements are determined from workplace instructions
1.2 Frame specifications and repair procedures are sourced and interpreted
1.3 Inspection and measurement options are analysed and those most appropriate to the circumstances are selected
1.4 Hazards associated with the work are identified and risks are managed
1.5 Inspection and measurement tools and equipment are selected and checked according to manufacturer procedures
2. Inspect and measure frame
2.1 Frame is inspected and repair requirements are determined according to workplace procedures and safety requirements
2.2 Inspection results are compared with manufacturer specifications
2.3 Inspection findings are reported according to workplace procedures, including recommendations for necessary repairs or adjustments
3. Repair frame
3.1 Repair procedures and information are sourced and interpreted
3.2 Repair options are analysed and those most appropriate to the circumstances are selected
3.3 Repair tools, equipment and materials are selected and checked for serviceability
3.4 Frame is repaired, replaced and adjusted according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
4. Align frame
4.1 Alignment procedures and information are sourced and interpreted
4.2 Alignment options are analysed and those most appropriate to the circumstances are selected
4.3 Alignment tools, equipment and materials are selected and checked according to manufacturer procedures
4.4 Frame is aligned according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
5. Complete work processes
5.1 Final inspection is made to ensure work is to workplace expectations and frame is presented ready for use or stored
5.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected
5.3 Tools and equipment are checked and stored according to workplace procedures
5.4 Workplace documentation is processed according to workplace procedures
Before competency can be determined, individuals must demonstrate they can perform the following according to the standards defined in this unit’s elements, performance criteria, range of conditions and foundation skills:
repair and align frames on two of the following motorcycles:
road fully fared
road naked
cruiser
off road
scooter.
Individuals must be able to demonstrate knowledge of:
work health and safety (WHS) and occupational health and safety (OHS) requirements relating to repairing and aligning motorcycle frames, including procedures for:
selecting and using personal protective equipment (PPE), including safety glasses, ear protection and safety footwear
lifting and supporting motorcycles
using motorcycle frame straightening rigs
types and application of motorcycle frames, including those of:
road fully fared motorcycles
road naked motorcycles
cruiser motorcycles
off road motorcycles
scooters
principles of frame alignment and steering geometry as applied to motorcycles
frame repair procedures, including application, purpose and operation of straightening jigs
frame alignment and adjustment procedures, including procedures for checking and adjusting swing arm alignment
regulatory requirements relating to repairing and aligning motorcycle frames, including Australian Design Rules.
Assessors must satisfy NVR/AQTF assessor requirements.
Competency is to be assessed in the workplace or a simulated environment that accurately reflects performance in a real workplace setting.
Assessment must include direct observation of tasks.
Where assessment of competency includes third-party evidence, individuals must provide evidence that links them to the motorcycle frames that they have repaired and aligned, e.g. repair orders.
Assessors must verify performance evidence through questioning on skills and knowledge to ensure correct interpretation and application.
The following resources must be made available:
automotive repair workplace or simulated workplace
two different motorcycles as specified in the performance evidence
motorcycle frame alignment jig
tools, equipment and materials appropriate for repairing and aligning motorcycle frames.
Submission Requirements
List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here
Assessment task 1: [title] Due date:
(add new lines for each of the assessment tasks)
Assessment Tasks
Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.
Elements
Elements describe the essential outcomes.
Performance Criteria
Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.
1. Prepare to inspect and measure motorcycle frame
1.1 Job requirements are determined from workplace instructions
1.2 Frame specifications and repair procedures are sourced and interpreted
1.3 Inspection and measurement options are analysed and those most appropriate to the circumstances are selected
1.4 Hazards associated with the work are identified and risks are managed
1.5 Inspection and measurement tools and equipment are selected and checked according to manufacturer procedures
2. Inspect and measure frame
2.1 Frame is inspected and repair requirements are determined according to workplace procedures and safety requirements
2.2 Inspection results are compared with manufacturer specifications
2.3 Inspection findings are reported according to workplace procedures, including recommendations for necessary repairs or adjustments
3. Repair frame
3.1 Repair procedures and information are sourced and interpreted
3.2 Repair options are analysed and those most appropriate to the circumstances are selected
3.3 Repair tools, equipment and materials are selected and checked for serviceability
3.4 Frame is repaired, replaced and adjusted according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
4. Align frame
4.1 Alignment procedures and information are sourced and interpreted
4.2 Alignment options are analysed and those most appropriate to the circumstances are selected
4.3 Alignment tools, equipment and materials are selected and checked according to manufacturer procedures
4.4 Frame is aligned according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
5. Complete work processes
5.1 Final inspection is made to ensure work is to workplace expectations and frame is presented ready for use or stored
5.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected
5.3 Tools and equipment are checked and stored according to workplace procedures
5.4 Workplace documentation is processed according to workplace procedures
This section specifies work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Bold italicised wording, if used in the performance criteria, is detailed below.
Safety requirements must include:
work health and safety (WHS) and occupational health and safety (OHS) requirements, including procedures for:
selecting and using personal protective equipment (PPE), including safety glasses, ear protection and safety footwear
lifting and supporting motorcycles
using motorcycle frame straightening rigs.
Before competency can be determined, individuals must demonstrate they can perform the following according to the standards defined in this unit’s elements, performance criteria, range of conditions and foundation skills:
repair and align frames on two of the following motorcycles:
road fully fared
road naked
cruiser
off road
scooter.
Individuals must be able to demonstrate knowledge of:
work health and safety (WHS) and occupational health and safety (OHS) requirements relating to repairing and aligning motorcycle frames, including procedures for:
selecting and using personal protective equipment (PPE), including safety glasses, ear protection and safety footwear
lifting and supporting motorcycles
using motorcycle frame straightening rigs
types and application of motorcycle frames, including those of:
road fully fared motorcycles
road naked motorcycles
cruiser motorcycles
off road motorcycles
scooters
principles of frame alignment and steering geometry as applied to motorcycles
frame repair procedures, including application, purpose and operation of straightening jigs
frame alignment and adjustment procedures, including procedures for checking and adjusting swing arm alignment
regulatory requirements relating to repairing and aligning motorcycle frames, including Australian Design Rules.
Assessors must satisfy NVR/AQTF assessor requirements.
Competency is to be assessed in the workplace or a simulated environment that accurately reflects performance in a real workplace setting.
Assessment must include direct observation of tasks.
Where assessment of competency includes third-party evidence, individuals must provide evidence that links them to the motorcycle frames that they have repaired and aligned, e.g. repair orders.
Assessors must verify performance evidence through questioning on skills and knowledge to ensure correct interpretation and application.
The following resources must be made available:
automotive repair workplace or simulated workplace
two different motorcycles as specified in the performance evidence
motorcycle frame alignment jig
tools, equipment and materials appropriate for repairing and aligning motorcycle frames.
Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.
Observation Checklist
Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice
Yes
No
Comments/feedback
Job requirements are determined from workplace instructions
Frame specifications and repair procedures are sourced and interpreted
Inspection and measurement options are analysed and those most appropriate to the circumstances are selected
Hazards associated with the work are identified and risks are managed
Inspection and measurement tools and equipment are selected and checked according to manufacturer procedures
Frame is inspected and repair requirements are determined according to workplace procedures and safety requirements
Inspection results are compared with manufacturer specifications
Inspection findings are reported according to workplace procedures, including recommendations for necessary repairs or adjustments
Repair procedures and information are sourced and interpreted
Repair options are analysed and those most appropriate to the circumstances are selected
Repair tools, equipment and materials are selected and checked for serviceability
Frame is repaired, replaced and adjusted according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
Alignment procedures and information are sourced and interpreted
Alignment options are analysed and those most appropriate to the circumstances are selected
Alignment tools, equipment and materials are selected and checked according to manufacturer procedures
Frame is aligned according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
Final inspection is made to ensure work is to workplace expectations and frame is presented ready for use or stored
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected
Tools and equipment are checked and stored according to workplace procedures
Workplace documentation is processed according to workplace procedures
Job requirements are determined from workplace instructions
Frame specifications and repair procedures are sourced and interpreted
Inspection and measurement options are analysed and those most appropriate to the circumstances are selected
Hazards associated with the work are identified and risks are managed
Inspection and measurement tools and equipment are selected and checked according to manufacturer procedures
Frame is inspected and repair requirements are determined according to workplace procedures and safety requirements
Inspection results are compared with manufacturer specifications
Inspection findings are reported according to workplace procedures, including recommendations for necessary repairs or adjustments
Repair procedures and information are sourced and interpreted
Repair options are analysed and those most appropriate to the circumstances are selected
Repair tools, equipment and materials are selected and checked for serviceability
Frame is repaired, replaced and adjusted according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
Alignment procedures and information are sourced and interpreted
Alignment options are analysed and those most appropriate to the circumstances are selected
Alignment tools, equipment and materials are selected and checked according to manufacturer procedures
Frame is aligned according to manufacturer specifications, workplace procedures, and safety requirements, and without causing damage to components or systems
Final inspection is made to ensure work is to workplace expectations and frame is presented ready for use or stored
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected
Tools and equipment are checked and stored according to workplace procedures
Workplace documentation is processed according to workplace procedures
Forms
Assessment Cover Sheet
AURJTY001 - Repair and align motorcycle frames
Assessment task 1: [title]
Student name:
Student ID:
I declare that the assessment tasks submitted for this unit are my own work.
Student signature:
Result: Competent Not yet competent
Feedback to student
Assessor name:
Signature:
Date:
Assessment Record Sheet
AURJTY001 - Repair and align motorcycle frames
Student name:
Student ID:
Assessment task 1: [title] Result: Competent Not yet competent
(add lines for each task)
Feedback to student:
Overall assessment result: Competent Not yet competent