This unit describes the performance outcomes required to remove, inspect and fit earthmoving and off-the-road (OTR) tyres to construction and mining vehicles. It involves removing the tyre from the rim, identifying and controlling risks, inspecting the tyre, assembling the wheel and rim, recommending required repair action, inflation, deflation, and preparing the tyre, wheel and rim assembly for use or storage.

It applies to those who fit tyres to wheel and rim assemblies of not less than 600 mm (24 inches) nominal diameter.

Licensing, legislative, regulatory, Australian standards or certification requirements may apply to this unit in some jurisdictions. Users are advised to check with the relevant regulatory authority.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

This section specifies work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included.

Safety requirements must include:	those prescribed under applicable standards, WHS Acts and regulations, and workplace policies and procedures isolation procedures hazard control manual-handling techniques personal protective clothing and equipment using tools and equipment working with hazardous substances, including: nitrogen gas chemicals hydraulic pressure compressed air polyurethane resin (PUR) tyre fill tyre additive
Tools and equipment must include:	tyre handling equipment bead breakers rim and wheel assembly stands inspection stands hand tools inflation and deflation tools and pressure gauges lock ring catcher mufflers pneumatic tools hydraulic tools power tools soft face hammers support stands or jacks torque tools tyre levers wire brushes air compressors gauges
Hazardous conditions must include:	changing and unstable ground conditions dust sparks from use of grinders hard, soft or uneven ground conditions line of fire during inflation of tyre, wheel or rim assembly noise vehicles/pedestrians/machinery/other personnel within the workplace handling of tyres, rim components and assemblies
Hazardous tyre and wheel or rim conditions must include:	damage wear corrosion foreign material cracks heat damage, including pyrolysis compatibility of rim components hazardous fill substances, including nitrogen gas, calcium chloride and polyurethane resin (PUR) under- or over-inflated tyre
Rim and wheel component assemblies must include:	adaptor rings and plates bolts cleats nuts reducers spacer bands studs washers wedge bands wedges

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Identify and control hazardous conditions in the work environment
Identify and apply safety requirements to control hazardous tyre, wheel and rim assembly conditions, noting points where safety checks are required
Obtain and interpret emergency procedures and be prepared for fires, accidents and emergencies
Identify hazards and environmental issues, assess potential risks, and implement control measures in line with workplace policies
Obtain and interpret manufacturer procedures original equipment manufacturer (OEM) specifications, workplace procedures, and applicable standards for earthmoving and off-the-road tyres
Obtain, interpret, clarify and confirm work requirements
Plan sequence of work, noting points where safety checks are required
Select and wear personal protective equipment required for the work activity
Coordinate and communicate planned activities with others at the site as per work requirements
Identify tyre, wheel and rim components
Select and inspect tools and equipment according to manufacturer instructions and workplace procedures
Prepare, clean and inspect tyre, wheel and rim assembly for damage, wear, corrosion, foreign material, cracks, and compatibility of component
Isolate, jack, raise and support vehicle according to workplace procedures
Deflate tyre according to manufacturer instructions and workplace procedures
Verify appropriate deflation of tyre in line with workplace procedures and OEM requirements
Apply workplace procedures for the safe removal and purging of hazardous fill substances
Remove tyre according to workplace procedures and without causing component damage or injury
Clean and visually inspect tyre, wheel or rim for serviceability and compatibility for application according to workplace procedures and OEM specifications
Record and report inspection findings according to workplace procedures
Document recommended repair and replacement actions and report to relevant personnel according to workplace procedures
Access and interpret workplace procedures and OEM specifications for fitting tyres
Assess need for tyre additive and nitrogen and add where required
Fit tyre according to workplace and manufacturer procedures
Perform post-fit inspections of tyre, wheel and rim assembly according to workplace procedures to confirm correct assembly, component compatibility, serviceability, and correct seating of components prior to inflation
Identify and apply tyre inflation safety procedures
Inflate tyre for transport, storage or use according to workplace procedures and manufacturer specifications
Monitor tyre, wheel and rim assembly during inflation according to workplace procedures
Perform final inspection to ensure work meets workplace requirements and OEM requirements
Prepare tyre, wheel and rim assembly for use or storage according to workplace procedures
Inspect and store tools and equipment according to workplace procedures, tagging or reporting where necessary
Complete workplace documentation according to workplace procedures

Assessment Cover Sheet

AURKTJ011 - Remove, inspect and fit earthmoving and off-the-road tyres

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

AURKTJ011 - Remove, inspect and fit earthmoving and off-the-road tyres

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: