This unit of competency defines the skills and knowledge required to disconnect and reconnect equipment to all voltage levels up to1000 volts a.c./1500 volts d.c.

Where the selection and use of power tools/hand held operations is required unit MEM18002 Use power tools/hand held operations should also be selected.

Some jurisdictions may require the holder of this unit to be licensed or certified and users should check with the relevant authorities.

Band:

This unit has dual status and is to be regarded as both a specialisation Band A unit and Specialisation Band B unit for progression to C7 (AQF level IV).

Unit Weight: 3

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

This field allows for different work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included.
Equipment includes:	as defined in the licensing requirements, including electric motors, modular sensing switches and limit switches
Electrical isolation includes:	safe disconnection of all electrical power to equipment or equipment supply circuits via switching, circuit breakers or fuses on circuits/equipment using up to 1000 volts a.c. or 1500 volts d.c. single or multi-phase supply
Test equipment and tools include one (1) or more of the following:	voltmeters multimeters tong testers
Connect equipment includes:	reconnection of existing equipment or the replacement on a 'like for like' basis with no alteration to existing fixed wiring and also includes the original connection of fixed wired equipment

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Determine electrical characteristics of equipment and circuit by reference to circuit drawings, schematics, reference manuals, equipment specifications, identification plate and/or consultation with technical adviser
Determine and record equipment characteristics, including direction of rotation, where appropriate
Identify point/s of electrical isolation and isolate equipment in accordance with procedures
Use all lock-off equipment and signage requirements appropriately
Prove electrical isolation using appropriate techniques, procedures and test equipment
Note, record and label conductor layout
Disconnect conductors and terminate and make safe disconnected cables/connections
Identify characteristics of the equipment to be connected and determine connection requirements
Check circuit for safe isolation using appropriate test equipment, procedures and techniques
Check connections and prepare conductors for termination
Connect conductors to equipment in accordance with specifications and regulatory requirements
Fasten/seal all cables/wires/conduit to specifications
Remove all lock-off equipment and signage
Check and test equipment and circuit for compliance with specifications and regulatory and legislative requirements
Follow standard operating procedures (SOPs)
Determine electrical characteristics of equipment and circuit by reference to circuit drawings, schematics, reference manuals, equipment specifications, identification plate and/or consultation with technical adviser
Identify characteristics of the equipment to be connected and determine connection requirements
Assess situation to identify points of danger to the injured person and potential rescuer

Assessment Cover Sheet

MEM18049 - Disconnect/reconnect fixed wired equipment up to 1000 volts a.c./1500 volts d.c.

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

MEM18049 - Disconnect/reconnect fixed wired equipment up to 1000 volts a.c./1500 volts d.c.

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: