This unit describes the skills and knowledge required to prepare and apply thin-film rollcoat resin flooring systems.

This unit applies to flooring technicians working in accordance with pre-determined work orders.

Licensing, legislative or certification requirements may apply to this unit and relevant state/territory and local government agencies should be consulted to determine any necessary certification or licensing for undertaking flooring work. Access to construction sites requires certification of general induction training specified by the National Code for Induction for Construction Work (ASCC 2007).

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Identify and follow work health and safety legislative, and organisational requirements
Correctly interpret work orders and confirm job requirements
Select and check tools and equipment for suitability, serviceability and safety prior to use
Plan application with respect to specified film thickness and/or consumption, cutting in, boundaries, seams, joints and exit points
Inspect condition of the mechanically prepared subfloor and confirm suitability for required finish consistent with manufacturer recommendations
Remove dust and debris from the substrate prior to application, and control sources
Establish mixing area in suitable area and select surface protection measures and apply to areas not being coated
Check coating materials for correct quantities, undamaged packaging and no obvious discrepancies in colour and viscosity
Select suitable masking tape and correctly apply to mark off edges, transitions and other floor boundaries
Correctly fit personal protective equipment (PPE) before coating materials are handled
Accurately measure and mix component quantities in accordance with supplier instructions
Apply mixed basecoat in accordance with supplier application notes
Prepare cured basecoat for topcoat application in accordance with supplier application notes
Apply mixed topcoat in accordance with supplier application notes
Check coating applications for quality at each stage and rectify any deficiencies
Check, clean and store tools and equipment in accordance with workplace procedures
Seal and store unused coating materials in accordance with supplier instructions
Clean work area and dispose of rubbish safely
Accurately complete required workplace and project documentation
Identify and follow work health and safety legislative, and organisational requirements
Correctly interpret work orders and confirm job requirements
Select and check tools and equipment for suitability, serviceability and safety prior to use
Plan application with respect to specified film thickness and/or consumption, cutting in, boundaries, seams, joints and exit points
Inspect condition of the mechanically prepared subfloor and confirm suitability for required finish consistent with manufacturer recommendations
Remove dust and debris from the substrate prior to application, and control sources
Establish mixing area in suitable area and select surface protection measures and apply to areas not being coated
Check coating materials for correct quantities, undamaged packaging and no obvious discrepancies in colour and viscosity
Select suitable masking tape and correctly apply to mark off edges, transitions and other floor boundaries

Assessment Cover Sheet

MSFFL3072 - Mix and apply thin-film rollcoat resin flooring systems

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

MSFFL3072 - Mix and apply thin-film rollcoat resin flooring systems

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: