List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. |
1 | Identify the purpose of the jig or fixture | 1.1 | Purpose of the jig or fixture, and the equipment it is to be used on is established |
| | 1.2 | Proposed service life of jig or fixture is established |
| | 1.3 | Tolerances allowed are identified |
| | 1.4 | Materials for jig construction are established |
| | 1.5 | Quality requirements for each stage of the construction process are identified |
2 | Plan jig or fixture construction | 2.1 | Plan of proposed jig or fixture is produced |
| | 2.2 | Approval of design is gained through workplace procedures |
| | 2.3 | Steps or stages in production are planned, noting check points for measurements and tests |
3 | Collect materials and equipment | 3.1 | Work health and safety (WHS) requirements, including personal protection needs, are observed throughout the work |
| | 3.2 | Sufficient materials to complete the project are assembled ready for use |
| | 3.3 | Suitable work area is selected |
| | 3.4 | Hand and/or power tools are identified and checked for serviceability and assembled in work area |
| | 3.5 | Appropriate equipment required is identified and checked for serviceability |
4 | Construct the jig or fixture | 4.1 | Production plan is followed to construct the jig or fixture |
| | 4.2 | Tools and equipment are used in accordance with workplace procedures |
| | 4.3 | Quality checks are conducted at the identified points |
| | 4.4 | Modifications are identified and recommended within workplace procedures |
| | 4.5 | Modifications to the plan are documented and followed |
| | 4.6 | Jig or fixture is checked for fitness for purpose |
5 | Finalise operation and maintain equipment | 5.1 | Work area is cleaned, hand and/or power tools and equipment are cleaned, maintained and stored in accordance with workplace procedures |
| | 5.2 | Machinery is cleaned and left in a safe mode |
| | 5.3 | Faulty and/or defective equipment is tagged and reported in accordance with workplace practices |
| | 5.4 | Unused hardware is collected and stored for re-use or disposal following workplace procedures |
| | 5.5 | Waste and scrap materials are dealt with following workplace procedures |
Interpret work order and locate and apply information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self or others
prevent damage to goods, tools, equipment or products
maintain required production output and product quality
Select materials and construct a minimum of three (3) different types of jigs/fixtures, including one (1) for a shaping machine and one (1) which is adjustable
Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements
Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures
Minimise wastage of resources, including materials, time and money
Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity
Types, characteristics, uses and limitations of jigs and fixtures
Criteria for selecting material for use in jigs and fixtures
Requirements for cutting, shaping and joining materials
Identification of equipment, processes and procedures
Work flow in relation to the use of jigs and fixtures
Assessors must:
hold training and assessment competencies as determined by the National Skills Standards Council (NSSC) or its successors
have vocational competency in the furnishing industry at least to the level being assessed with broad industry knowledge and experience, usually combined with a relevant industry qualification
be familiar with the current skills and knowledge used and have relevant, current experience in the furnishing industry.
Assessment methods must confirm consistency of performance over time rather than a single assessment event and in a range of workplace relevant contexts.
Assessment must be by observation of relevant tasks with questioning on underpinning knowledge and, where applicable, multimedia evidence, supervisor’s reports, projects and work samples.
Assessment is to be conducted on single units of competency or in conjunction with other related units of competency. Foundation skills are integral to competent performance in the unit and should not be assessed separately.
Assessment must occur on the job or in a workplace simulated facility with relevant process, equipment, materials, work instructions and deadlines.
Access is required to a job context, materials and equipment for jig or fixture construction.