List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. |
1 | Perform pre-start checks | 1.1 | Check all emergency stops, guards and controls |
| 1.2 | Identify requirements for materials, quality and production run |
| 1.3 | Check and adjust equipment as required |
| 1.4 | Check that the equipment has been set-up correctly |
|
2 | Carry out pre-start operations to procedures | 2.1 | Restore all power to the machine and ancillary equipment |
| 2.2 | Start up the ancillary equipment and set the temperature and other controllers as required |
| 2.3 | Check all machine settings as required |
| 2.4 | Select and load the correct raw material |
| 2.5 | Charge, purge and clean machine as required |
|
3 | Start machine and hand over to operator | 3.1 | Start and check machine |
| 3.2 | Adjust machine as required to bring to operational speed/ condition |
| 3.3 | Check and run machine until a quality product is obtained |
| 3.4 | Make adjustments to machine and extra equipment in line to produce an acceptable product |
| 3.5 | Make any adjustments required to ensure the machine and its upstream and downstream extra equipment in line are in balance |
| 3.6 | Give the operator all necessary instructions and hand over the machine |
| 3.7 | Shut down machine as required |
|
4 | Anticipate and solve problems | 4.1 | Recognise a problem or a potential problem |
| 4.2 | Determine problems needing priority action |
| 4.3 | Refer problems outside area of responsibility to appropriate person, with possible causes |
| 4.4 | Seek information and assistance as required to solve problems |
| 4.5 | Solve problems within area of responsibility |
| 4.6 | Follow through items initiated until final resolution has occurred |
Evidence required to demonstrate competence in this unit must be relevant to and satisfy the requirements of the elements and performance criteria and demonstrate the ability to:
read and interpret procedures, job specifications, instruments/control panels, material labels and safety data sheets (SDS)
set up and adjust machine control system to produce product to specification, including one or more of:
basic controls
open loop
closed loop
shot size and correction capacity
speed/cycle time
screw position
equipment/process pressure
clamp pressure
time
screw speed
screw back pressure
screw back time
melt decompress position
sprue break
start up process and monitor key variables, including:
equipment condition
set up variables
product measurements
product integrity and general conformance to specification
make adjustments to process to:
remedy faults and nonconformity
establish a stable process
establish balance with upstream and downstream processes
give instructions to the operator and handover over the machine
safely shut down equipment in normal and abnormal circumstances
identify hazards and apply relevant hazard controls
apply safety procedures
apply housekeeping procedures
apply waste management procedures
recognise early warning signs of equipment/processes needing attention or with potential problems
distinguish between causes of problems, including:
operational problems
instrument failure/malfunction
electrical failure/malfunction
mechanical failure/malfunction
wrong readings
equipment design deficiencies
polymer properties
process variables
recognise and prioritise problems requiring action
resolve non-routine problems
communicate effectively with team/work group and supervisors
complete workplace records
do basic arithmetical manipulations, including additions, subtractions, divisions, fractions and percentages.
Must provide evidence that demonstrates knowledge relevant to their job sufficient to operate independently and to solve routine and non-routine problems, including knowledge of:
function and operating principles of machine and components
products, materials and material characteristics
behaviour of materials in relation to key process variables
quality requirements at each production stage
function of and readings from measuring instruments, including one or more of:
levelling
thermocouples
pyrometers
transducers
thermometers
pressure gauges
vacuum gauges
flow meters
purpose and operation of safety interlocks and systems, including one or more of:
limit switches
normally open/normally closed
overstroke control systems
hydraulic temperature control
material temperature control
machine guards
nozzle purge guard
mould protection systems
ejection limit switches
impact of machine operating parameters on product quality and production output
factors which may affect product quality or production output and appropriate remedies
polymer properties and their interactions with process conditions
impact of variations in raw materials and equipment operation in relation to final product
routine and non-routine problems that may arise, the range of possible causes and appropriate actions
organisation procedures relevant to the work environment/job role
hierarchy of control
hazards that may arise in the job/work environment and:
their possible causes
potential consequences
appropriate risk controls.
The unit should be assessed holistically and the judgement of competence shall be based on a holistic assessment of the evidence.
The collection of performance evidence is best done from a report and/or folio of evidence drawn from:
a single project which provides sufficient evidence of the requirements of all the elements and performance criteria
multiple smaller projects which together provide sufficient evidence of the requirements of all the elements and performance criteria.
A third-party report, or similar, may be needed to testify to the work done by the individual, particularly when the project has been done as part of a project team.
Assessment should use a real project in an operational workplace. Where this is not possible or where personal safety or environmental damage are limiting factors assessment must occur using a sufficiently rigorous simulated environment that reflects realistic operational workplace conditions. This must cover all aspects of workplace performance, including environment, task skills, task management skills, contingency management skills and job role environment skills.
Assessment in a simulated environment should use evidence collected from demonstration of skills and one or more of:
walk-throughs
pilot plant operation
industry-based case studies/scenarios
‘what ifs’.
Knowledge evidence may be collected concurrently with performance evidence or through an independent process, such as workbooks, written assessments or interviews.
Assessment processes and techniques must be appropriate to the language, literacy and numeracy requirements of the work being performed and the needs of the candidate.
Conditions for assessment must include access to all tools, equipment, materials and documentation required, including relevant workplace procedures, product and manufacturing specifications associated with this unit.
The regulatory framework will be reflected in workplace policies and procedures and is not required to be independently assessed.
Foundation skills are integral to competent performance of the unit and should not be assessed separately.
Assessors must satisfy the assessor competency requirements that are in place at the time of the assessment as set by the VET regulator.
In addition the assessor or anyone acting in subject matter expert role in assessment shall demonstrate both technical competency and currency. If the assessor cannot demonstrate technical competency and currency they shall assess with a subject matter expert who does meet these requirements.
Technical competence can be demonstrated through one or more of:
relevant VET or other qualification/Statement of Attainment
appropriate workplace experience undertaking the type of work being assessed under routine and non-routine conditions
appropriate workplace experience supervising/evaluating the type of work being assessed under routine and non-routine conditions
Currency can be demonstrated through one or more of:
being currently employed undertaking the type of work being assessed
being employed by the organisation undertaking the type of work being assessed and having maintained currency in accordance with that organisation’s policies and procedures
having consulted/had contact with an organisation undertaking the type of work being assessed within the last twelve months, the consultation/contact being related to assessment
conducting on the job training/assessments of the type of work being assessed
being an active member of a relevant professional body and participating in activities relevant to the assessment of this type of work.