This unit describes the skills and knowledge required to manage selection and monitor condition, repair and disposal processes for off-the-road (OTR) and earthmoving vehicle’s tyres, wheels and rim assemblies.

This unit is appropriate for those working in tyre fitting supervisory roles. It applies to those who work with tyres, wheels and rim assemblies of not less than 600mm (24 inches) nominal diameter.

Licensing, legislative, regulatory, Australian Standards or certification requirements may apply to this unit and can vary between states, territories, and industry sectors, and must be sourced from relevant state jurisdictions prior to application of the unit.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

RIISAM210D Remove and fit wheel assemblies; and

RIISAM211D Remove, repair and refit tyres and tubes;

OR

AURKTJ011 Remove, inspect and fit earthmoving and off-the-road tyres; and

AURKTJ012 Remove, inspect and fit earthmoving and off-the-road wheel and rim assemblies.

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Confirm technical, operational and economic requirements of tyres, wheels or rim assemblies in line with workplace procedures
Obtain information from authorised manufacturer(s) on the options for tyres, wheels or rim assemblies in line with workplace procedures
Analyse tyre, wheel or rim assembly options to identify technical compliance, economic benefits and meeting operational requirements in line with workplace procedures
Select tyres, wheels or rim assemblies based on analysis and procure according to workplace procedures
Coordinate receipt of tyres, wheels or rim assemblies and transportation to required location in line with workplace procedures
Arrange storage of tyres, wheels or rim assemblies according to workplace procedures
Complete documentation for newly procured tyres, wheels and rim assemblies according to workplace procedures, including registering information on workplace asset management systems within scope of own responsibilities
Set-up maintenance schedule for tyres, wheels and rim assemblies in line with workplace procedures
Coordinate and manage resources to meet the requirements of the maintenance schedule
Supervise inspection of tyres, wheels or rim assemblies according to maintenance schedule or reported issues
Perform fault identification of tyres, wheels or rim assemblies during inspection and rectify within scope of own responsibility and according to workplace procedures
Update maintenance schedule for tyres, wheels and rim assemblies based on condition and wear
Identify authorised contractors to repair tyres, wheels or rim assemblies in line with workplace procedures
Coordinate transportation of tyres, wheels or rim assemblies to and from the repair contractor in line with workplace procedures
Inspect tyres, wheels or rim assemblies on return from repair contractor to confirm compliance with workplace procedures
Confirm when tyres, wheels or rim assemblies are no longer fit for service
Arrange disposal or recycle tyres, wheels or rim assemblies as per workplace procedures
Complete and file or distribute documentation in a manner that complies with workplace practices

Assessment Cover Sheet

RIISAM315A - Manage tyre, wheel and rim assembly applications

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

RIISAM315A - Manage tyre, wheel and rim assembly applications

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: