This unit involves the skills and knowledge required to operate and monitor heat exchangers and cooling systems within power generation facilities.

Aheat exchangeris used inpower generation facilities to maintain efficiency in the steam and water cycle. The cooling system is used to reduce the heat from power generation plant and/or equipment.

Competency in this unit requires the ability to plan work, operate heat exchangers and cooling system plant, test heat exchangers and cooling system plant, analyse heat exchangers and cooling system plant faults, monitor and inspect heat exchangers and cooling system plant and the completion of all documentation. Individuals will, in general, work under supervision, in a power plant as an operator.

Power generation plant operators are typically trained and authorised to isolate, prepare plant and issue permits to work.

No licensing, legislative or certification requirements apply to this unit at the time of publication.

Note: Workplace practice

The application of the skills and knowledge described in this unit may require a licence or training permit to practice in the workplace where work is carried out on gas and electrical installations. Additional conditions may apply under state and territory legislative and regulatory licensing requirements.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Range is restricted to essential operating conditions and any other variables essential to the work environment. Non-essential conditions may be found in the Companion Volume Implementation Guide.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Safety issues related to operating and monitoring heat exchangers and cooling system plant are identified, in accordance with workplace procedures and Work, Health and Safety (WHS)/Occupational Health and Safety(OHS) regulations and legislative requirements
Work requirements are identified, in accordance with workplace procedures, from relevant personnel and documentation
Documentation to determine heat exchangers and cooling system plant status is assessed and evaluated, in accordance with workplace procedures
Inspection and field preparation for heat exchangers and cooling system plant service is carried out, in accordance with workplace procedures and manufacturers' recommendations
Heat exchangers and cooling system plant operational prerequisites are established, in accordance with workplace procedures and manufacturers' recommendations
Sequence for recommissioning of heat exchangers and cooling system plant is determined, in accordance with workplace procedures and site requirements
Heat exchangers and cooling system plant is operated, in accordance with workplace procedures and manufacturers' operating recommendations
Operational tests are performed, in accordance with workplace procedures
Causes of abnormal heat exchangers and cooling system plant operating conditions are identified, in accordance with workplace procedures, and by analysing technical and operational information
Heat exchangers and cooling system plant to be monitored and inspected is physically identified, in accordance with workplace procedures
Heat exchangers and cooling system plant problems, movements, and status are reported, in accordance with workplace procedures

Assessment Cover Sheet

UEPOPS330 - Operate and monitor heat exchangers and cooling systems

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

UEPOPS330 - Operate and monitor heat exchangers and cooling systems

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: