Unit of Competency Mapping – Information for Teachers/Assessors – Information for Learners

FBPSUG2025 Mapping and Delivery Guide
Perform general planing and shaping operations

Version 1.0
Issue Date: May 2024


Qualification -
Unit of Competency FBPSUG2025 - Perform general planing and shaping operations
Description
Employability Skills
Learning Outcomes and Application This unit of competency describes the skills and knowledge required to carry out general planing and shaping operations. It excludes the use of CNC planers and shapers. Typical operations include slotting, planing and cutting flats.The unit applies to individuals who work under supervision in the sugar milling industry. All work must be carried out to comply with workplace procedures according to state/territory health and safety regulations, legislation and standards that apply to the workplace.No occupational licensing, legislative or certification requirements apply to this unit at the time of publication.
Duration and Setting X weeks, nominally xx hours, delivered in a classroom/online/blended learning setting.
Prerequisites/co-requisites
Competency Field
Development and validation strategy and guide for assessors and learners Student Learning Resources Handouts
Activities 		Slides
PPT 		Assessment 1 Assessment 2 Assessment 3 Assessment 4
Elements of Competency Performance Criteria              
Element: Prepare for planing and shaping operations
  • Identify machining requirements according to job specifications
  • Select, fit and use personal protective equipment according to health and safety procedures in the workplace
  • Collect and prepare materials to be planed or shaped
  • Set up planing and shaping equipment for operation
  • Conduct pre-operational equipment checks according to operating procedures
  • Identify and report health and safety hazards and maintenance requirements according to health and safety procedures
       
Element: Operate planing and shaping equipment to achieve specifications
  • Set machining parameters to meet job requirements
  • Position and clamp materials for planing and shaping operation
  • Start, operate and shut down the planing and shaping equipment according to operating procedures
  • Check work against specifications
  • Identify non-conforming components, and correct as required
  • Undertake basic routine operational maintenance according to workplace procedures
  • Ensure the work area is maintained to meet workplace cleaning standards
       

Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assignment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.
Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
Identify machining requirements according to job specifications 
Select, fit and use personal protective equipment according to health and safety procedures in the workplace 
Collect and prepare materials to be planed or shaped 
Set up planing and shaping equipment for operation 
Conduct pre-operational equipment checks according to operating procedures 
Identify and report health and safety hazards and maintenance requirements according to health and safety procedures 
Set machining parameters to meet job requirements 
Position and clamp materials for planing and shaping operation 
Start, operate and shut down the planing and shaping equipment according to operating procedures 
Check work against specifications 
Identify non-conforming components, and correct as required 
Undertake basic routine operational maintenance according to workplace procedures 
Ensure the work area is maintained to meet workplace cleaning standards 

Forms

Assessment Cover Sheet

FBPSUG2025 - Perform general planing and shaping operations
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

FBPSUG2025 - Perform general planing and shaping operations

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: