List each assessment task's title, type (eg project, observation/demonstration, essay, assignment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Range is restricted to essential operating conditions and any other variables essential to the work environment. Non-essential conditions may be found in the Companion Volume Implementation Guide.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Task requirements are identified from work orders or equivalent and confirmed with relevant people and a site inspection is completed in accordance with workplace procedures
Work area ground/operating surface is assessed to determine suitability for operational use of EWP in accordance with manufacturer requirements and workplace procedures
EWP capabilities are established for the load/s and work/task requirements in accordance with manufacturer requirements and workplace procedures
Appropriate paths for operating the EWP and moving in work area are assessed and determined in accordance with workplace procedures
Relevant hazard and risk control measures are applied and advised to relevant person/s in accordance with workplace procedures
Traffic management plan implementation is confirmed in accordance with workplace procedures
Appropriate communication procedures are identified, with relevant people in accordance with workplace procedures
All work is confirmed to ensure coverage of work/task requirements for the relevant work area in accordance with workplace procedures
Consultation with workplace person/s is maintained to ensure workplan is clear and consistent with site requirements in accordance with workplace procedures
Risk control measures for hazards identified are checked for implementation in accordance with workplace procedures
Safety equipment including Personal Protective Equipment (PPE) are inspected, fitted correctly and used in accordance with manufacturer requirements and safe work procedures
EWP is accessed in a safe manner in accordance with manufacturer requirements and safe work procedures
Pre-start EWP checks are carried out in accordance with manufacturers requirements and safe work procedures
EWP is started and is checked for any abnormal noises in accordance safe work procedures
EWP is positioned correctly as per work plan in work area in accordance with relevant manufacturer requirements and safe work procedures
EWP is stabilised appropriately in accordance with the workplan, relevant manufacturer requirements and safe work procedures
Operational checks from base controls are carried out in accordance with relevant manufacturer requirements and safe work procedures
All platform controls are located, identified and tested in accordance with manufacturer requirements and safe work procedures
All damage and defects are reported and appropriate action is taken to rectify in accordance with manufacturer requirements and safe work procedures
EWP logbook is inspected and is correct for the EWP, is completed and signed in accordance with manufacturer requirements and safe work procedures
Weather and work environmental conditions are assessed to determine any impact on EWP operation and positioning as per workplan in accordance with manufacturer requirements and safe work procedures
Relevant hazard prevention/control measures identified are checked for implementation in accordance with safe work procedures
EWP is safely located at point of work in work area in accordance with safe work procedures
EWP platform is positioned for work tasks and stability and all operations are monitored constantly in accordance with safe work procedures
Work gear and tools are stowed and secured in accordance with safe work procedures
EWP is operated using all movements in accordance with safe work procedures and manufacturer requirements
Unplanned and unsafe situations are responded to in accordance with safe work procedures
All communication signals are correctly interpreted and followed whilst EWP is operated in accordance with safe work procedures
EWP platform is accessed and egressed in accordance with safe work procedures and manufacturer requirements
EWP is parked, switched off and isolated appropriately in accordance with manufacturer requirements and safe work procedures
Post-operational EWP checks are carried out in accordance with manufacturer requirements and safe work procedures
EWP boom is retracted, lowered, stowed and secured in accordance with manufacturer requirements and safe work procedures
Safety equipment and PPE is disconnected from platform in accordance with safe work procedures
Relevant motion locks and brakes are applied as required in accordance with manufacturer requirements and safe work procedures
Outriggers and/or stabilisers, plates or packing if fitted are stowed and secured in accordance and with manufacturer requirements and safe work procedures
EWP is shut down in accordance with manufacturer requirements and safe work procedures
Task requirements are identified from work orders or equivalent and confirmed with relevant people and a site inspection is completed in accordance with workplace procedures
Consultation with workplace person/s is maintained to ensure workplan is clear and consistent with site requirements in accordance with workplace procedures
Relevant hazard prevention/control measures identified are checked for implementation in accordance with safe work procedures
Post-operational EWP checks are carried out in accordance with manufacturer requirements and safe work procedures

Assessment Cover Sheet

TLILIC0005 - Licence to operate a boom-type elevating work platform (boom length 11 metres or more)

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

TLILIC0005 - Licence to operate a boom-type elevating work platform (boom length 11 metres or more)

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: