Unit of Competency Mapping – Information for Teachers/Assessors – Information for Learners

TLILIC0040 Mapping and Delivery Guide
Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)

Version 1.0
Issue Date: May 2024


Qualification -
Unit of Competency TLILIC0040 - Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)
Description
Employability Skills
Learning Outcomes and Application
Duration and Setting X weeks, nominally xx hours, delivered in a classroom/online/blended learning setting.
Prerequisites/co-requisites
Competency Field
Development and validation strategy and guide for assessors and learners Student Learning Resources Handouts
Activities 		Slides
PPT 		Assessment 1 Assessment 2 Assessment 3 Assessment 4
Elements of Competency Performance Criteria              
Element: Work area operating surface is confirmed to determine the quality of ground suitability for operational use of non-slewing mobile crane in accordance with workplace procedures
       
Element: Non-slewing mobile crane RC and the lifting gear working load limit (WLL) are established for the load/s and work/task requirements in accordance with manufacturer requirements and workplace procedures
       
Element: Appropriate paths for operating the mobile crane and moving and placing load/s in work area are assessed and determined in accordance with workplace procedures
       
Element: Relevant hazard identification and risk elimination/control measures are applied and advised to associated personnel in accordance with workplace procedures
       
Element: Traffic management plan implementation is confirmed and followed in accordance with workplace procedures
       
Element: Appropriate communication procedures are identified and tested with associated personnel in accordance with workplace procedures
       
Element: All tasks are confirmed to ensure requirements for the relevant work area in accordance with a lift plan and workplace procedures
       
Element: Information required to ensure that lifting equipment and gear inspection, use, maintenance and storage complies with manufacturer requirements is obtained and interpreted
  • Consultation with workplace personnel is established and maintained to ensure lift plan is clear and consistent with site requirements in accordance with a lift plan and workplace procedures
       
Element: Risk control measures for hazards identified are checked for implementation in accordance with the lift plan and safe work procedures
       
Element: Non-slewing mobile crane is accessed safely in accordance with manufacturer requirements and safe work procedures
       
Element: Pre-start crane checks are carried out and any damage and defects are reported, recorded and appropriate action is taken in accordance with manufacturer requirements and safe work procedures
       
Element: Mobile crane is set up correctly with any lifting gear in accordance with lift plan, relevant manufacturer requirements, including load charts, and safe work procedures
       
Element: Fly jib (if fitted) is set up as required in accordance with specific manufacturer requirements and safe work procedures
       
Element: Operational checks are carried out and any damage and defects are reported, recorded and appropriate action is taken in accordance with manufacturer requirements and safe work procedures
       
Element: Crane logbook is checked to confirm current compliance is correct for the crane type, is completed and signed and required rectifications have been signed-off in accordance with manufacturer requirements and safe work procedures
       
Element: Weather and work environment conditions are assessed to determine any impact on mobile crane operations in accordance with manufacturer requirements and safe work procedures
       
Element: Weight of load is identified, calculated or estimated
       
Element: Derated WLL of lifting equipment resulting from selected slinging techniques is calculated
       
Element: Suitable lifting points and slinging techniques are identified
       
Element: Lifting equipment and gear are prepared for safe use
       
Element: Load destination is confirmed for stability ensuring it is able to bear the load and is prepared for safe access and landing
  • Lifts are determined within the RC of the non-slewing mobile crane in accordance with the load chart/s and lift plan
       
Element: Boom/jib and hook block are safely positioned over the load following directions from associated personnel in accordance with the lift plan and safe work procedures
       
Element: Lifting equipment and gear, where required, are connected to the load and used safely in accordance with the lift plan, safe work procedures and manufacturer requirements
       
Element: Test lift is carried out in accordance with safe work procedures
       
Element: Loads are transferred using relevant crane movements and tag lines, as required, in accordance with lift plan and safe work procedures
       
Element: Load and crane movement is monitored constantly and crane is operated safely in accordance with lift plan and safe work procedures
       
Element: All required communication signals are correctly interpreted and followed whilst crane is operated in accordance with the lift plan and safe work procedures
       
Element: Load is lowered and landed safely in accordance with lift plan and safe work procedures
       
Element: Lifting gear is disconnected from load and crane is positioned safely and efficiently for next task in accordance with lift plan and safe work procedures
       
Element: Lifting equipment and gear are inspected for defects, and defective items are isolated, tagged and reported
       
Element: Prepare to drive an articulated mobile crane
  • Any items on the crane body are safely and effectively restrained and loose components are stored in storage areas
       
Element: Pre-operational checks, including registrations and approvals, are completed for driving according to manufacturer instructions
       
Element: Tyre pressures and suspension settings are checked and set for driving and counterweights are positioned for road travel
       
Element: Boom and fall block are positioned for driving
       
Element: Appropriate signage, lights and equipment are checked for operational effectiveness and for conformity to prescribed traffic regulations or site traffic management plan
       
Element: Drive an articulated mobile crane
  • Articulated mobile crane is started, steered, manoeuvred, positioned and stopped in accordance with regulations, manufacturer instructions and relevant vehicle handling procedures and allowing for forward overhang of the boom
       
Element: Steering is maintained utilising ‘turn-in-turn-out’
       
Element: One-handed steering techniques are applied
       
Element: Braking system of articulated mobile crane is managed and operated efficiently to ensure effective control of vehicle under all conditions and allowing for greater stopping distance due to size, weight and forward projection of the boom
       
Element: Driving hazards are identified and/or anticipated and avoided or controlled through low risk driving
  • Crane boom/jib, lifting gear and associated equipment are stowed and secured as required in accordance with manufacturer requirements and safe work procedures
       
Element: Relevant motion locks and brakes are applied as required in accordance with manufacturer requirements and safe work procedures
       
Element: Crane is shut down and secured to prevent unauthorised access/use in accordance with safe work procedures
       
Element: Post-operational crane checks are carried out in accordance with legislative responsibilities, safe work procedures and manufacturer requirements
       

Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assignment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.
Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
 
 
 
 
 
 
 
Consultation with workplace personnel is established and maintained to ensure lift plan is clear and consistent with site requirements in accordance with a lift plan and workplace procedures 
 
 
 
 
 
 
 
 
 
 
 
 
Lifts are determined within the RC of the non-slewing mobile crane in accordance with the load chart/s and lift plan 
 
 
 
 
 
 
 
 
 
Any items on the crane body are safely and effectively restrained and loose components are stored in storage areas 
 
 
 
 
Articulated mobile crane is started, steered, manoeuvred, positioned and stopped in accordance with regulations, manufacturer instructions and relevant vehicle handling procedures and allowing for forward overhang of the boom 
 
 
 
Crane boom/jib, lifting gear and associated equipment are stowed and secured as required in accordance with manufacturer requirements and safe work procedures 
 
 
 

Forms

Assessment Cover Sheet

TLILIC0040 - Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

TLILIC0040 - Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: