This unit requires application of hand skills in the removal and installation of electrical hardware.

Applications include items of general electrical hardware fitted to fixed or rotary wing aircraft.

MEA101B

Interpret occupational health and safety practices in aviation maintenance

MEA103B

Plan and organise aviation maintenance work activity

MEA105C

Apply quality standards applicable to aviation maintenance processes

MEA107B

Interpret and use aviation maintenance industry manuals and specifications

MEA108B

Complete aviation maintenance industry documentation

MEA109B

Perform basic hand skills, standard trade practices and fundamentals in aviation maintenance

1. Remove general aircraft electrical hardware

1.1. System is rendered safe and prepared in accordance with the applicable maintenance manual and isolation tags are fitted where necessary to ensure personnel safety

1.2. Removal of electrical hardware is carried out in accordance with the applicable maintenance manual

1.3. Required maintenance documentation is completed and processed in accordance with standard enterprise procedures

1.4. Removed components are tagged, packaged or discarded in accordance with specified procedures

2. Install general aircraft electrical hardware

2.1. Electrical hardware components to be installed are checked to confirm correct part numbers, modification status, serviceability and shelf life

2.2. Physical installation of electrical hardware is carried out in accordance with the applicable maintenance manual

2.3. System is reinstated to correct physical condition in preparation for testing, as necessary

2.4. Required maintenance documentation is completed and processed in accordance with standard enterprise procedures

Required skills

Look for evidence that confirms skills in:

applying relevant OHS procedures

using approved maintenance documentation and aircraft publications relating to miscellaneous aircraft electrical hardware and components

recognising defects in and deterioration of electrical cables to aircraft industry standards, including crimped and soldered joints

correctly interpreting aircraft wire markings, terminal block identification and plug/socket pin numbering systems

inspecting electrical looms and harness pre and post-removal and installation to ensure minimum bends are maintained, cable is not in tension, plugs are correctly aligned, security of route ensures no chaffing of insulation, adequate clipping and cable ties have been utilised and construction complies with aircraft industry standards

positively identifying miscellaneous electrical hardware and/or components in all aircraft systems

plug connector pin removal and insertion

Required knowledge

Look for evidence that confirms knowledge of:

component attachment methods

connection of hardware and plugs

relevant OHS procedures

electrical wiring used in aircraft and wire marking

plug/socket pin numbering and terminal block identification

cable and loom installation requirements

crimping tools and crimp terminals

procedures for removal and insertion of plug connector pins

electrical fundamentals and related mathematical and physics principles

The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

A person who demonstrates competency in this unit must be able to apply hand skills, use specialist tools and use maintenance publications to remove and install items of general aircraft electrical hardware that are within the privileges of the CASA Aircraft Maintenance Engineer A Licence while observing all relevant safety precautions.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

It is essential that applicable cleanliness requirements and OHS safety precautions are fully observed, including awareness of electrostatic discharge procedures.

Evidence of transferability of skills and knowledge related to removal and installation is essential. An understanding of the attachment methods, connection of hardware and system operation as they relate to the work must be demonstrated before undertaking any action. The work plan should take account of applicable safety and quality requirements in accordance with the industry and regulatory standards.

A person cannot be assessed as competent until it can be demonstrated to the satisfaction of the workplace assessor that the relevant elements of the unit of competency are being achieved under supervision but without intervention on each of the connection methods 1 and 2 listed in the Range Statement. This shall be established via the records in the Log of Industrial Experience and Achievement or, where appropriate, an equivalent Industry Evidence Guide.

Context of and specific resources for assessment

Competency should be assessed in the workplace or simulated workplace using tools and equipment specified in maintenance manuals. It is also expected that general-purpose tools, test and ground support equipment found in most routine situations would be used where appropriate.

Method of assessment

Guidance information for assessment

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Note

Range statements listed below are numbered to facilitate specification of the assessment requirements included in the Evidence Guide

Removal and installation of electrical hardware

Removal and installation of electrical hardware involves one or more of the following connection methods:

1. Bolted

2. Plug connectors

Electrical hardware

Electrical hardware includes:

switches, relays, lamps, terminal blocks, current limiters, circuit breakers, fuses, sockets, potentiometers, capacitors, inductors, magnetic amplifiers, transformers, rheostats, miscellaneous sensors and minor components hard mounted throughout the aircraft, busbars, lugs, ferrules, splices, connectors and electrical, electronic cables and looms

Application of this unit may relate to:

scheduled maintenance up to the level of a weekly check, or to unscheduled maintenance involving component removal and installation

Procedures and requirements

Refer to industry standard procedures specified by manufacturers, regulatory authorities or the enterprise

This unit contains employability skills.