Application
This unit of competency covers using scarifying equipment in applications relating to floor preparation.
Licensing, legislative or certification requirements may apply to this unit and relevant state/territory and local government agencies should be consulted to determine any necessary certification or licensing for undertaking flooring work. Access to construction sites requires certification of general induction training specified by the National Code of Practice for Induction for Construction Work (ASCC 2007).
Elements and Performance Criteria
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. | ||
1 | Identify scarifying equipment | 1.1 | Applicable work health and safety (WHS), legislative and organisational requirements relevant to the use of scarifying equipment are verified and complied with |
1.2 | Types of scarifying equipment and their functions are identified from relevant information sources | ||
1.3 | Instructions and/or plans are read and interpreted to identify the process required to complete work tasks | ||
1.4 | Sources of power supply are recognised | ||
2 | Select scarifying equipment | 2.1 | Scarifying equipment and shot size are selected consistent with the needs of the job |
2.2 | Scarifying equipment is checked for serviceability and safety and any faults are correct or processed for repair | ||
3 | Clean and prepare sub-floor | 3.1 | Appropriate personal protective equipment is selected, correctly fitted and used |
3.2 | Fittings and fixtures are removed from the sub-floor | ||
3.3 | Sub-floor is cleared of loose debris and dirt, and cleaned | ||
4 | Scarify the floor | 4.1 | Work sequence and starting point are selected |
4.2 | Perimeter is prepared using an angle grinder | ||
4.3 | Main area is scarified using the most appropriate available equipment in accordance with Australian Standards or subsequent replacement standards | ||
4.4 | Floor area is cleaned, inspected and re-worked as required | ||
5 | Complete housekeeping | 5.1 | Tools and equipment are cleaned and stored appropriately |
5.2 | Work area is cleaned and rubbish disposed of appropriately | ||
5.3 | Workplace documentation is completed | ||
Evidence of Performance
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment and products
maintain required production output and product quality
Scarify a concrete sub-floor of a minimum of 10 sq. m to industry standards
Complete operator maintenance on scarifying equipment
Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements
Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures
Avoid backtracking, work flow interruptions or wastage
Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity
Evidence of Knowledge
State or territory WHS legislation, regulations, standards and codes of practice relevant to the use of scarifying equipment
Organisational and site standards, requirements, policies and procedures for preparing and presenting design information for the use of scarifying equipment
Types of scarifier attachments, their uses, capabilities and maintenance requirements
Characteristics, uses and limitations of the available shot sizes
Environmental protection requirements
Established communication channels and protocols
Relevant problem identification and resolution
Assessment Conditions
Assessors must:
hold training and assessment competencies as determined by the National Skills Standards Council (NSSC) or its successors
have vocational competency in the furnishing industry at least to the level being assessed with broad industry knowledge and experience, usually combined with a relevant industry qualification
be familiar with the current skills and knowledge used and have relevant, current experience in the furnishing industry.
Assessment methods must confirm consistency of performance over time rather than a single assessment event and in a range of workplace relevant contexts.
Assessment must be by observation of relevant tasks with questioning on underpinning knowledge and, where applicable, multimedia evidence, supervisor’s reports, projects and work samples.
Assessment is to be conducted on single units of competency or in conjunction with other related units of competency. Foundation skills are integral to competent performance in the unit and should not be assessed separately.
Assessment must occur on the job or in a workplace simulated facility with relevant process, equipment, materials, work instructions and deadlines.
Access is required to access to scarifying equipment and attachments, manufacturer/user instructions and/or manuals and a realistic scarifying task.
Foundation Skills
Foundation skills essential to performance are explicit in the performance criteria of this unit of competency. Detail on appropriate performance levels for each furnishing unit of competency in reading, writing, oral communication and numeracy utilising the Australian Core Skills Framework (ACSF) are provided in the Furnishing Training Package Implementation Guide.
Range Statement
Specifies different work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Range is restricted to essential operating conditions and any other variables essential to the work environment. | |
Unit context includes: | WHS requirements, including legislation, building codes, material safety management systems, hazardous and dangerous goods codes, and local safe operating procedures or equivalent work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements work requires individual to demonstrate some discretion, judgement and problem solving |
Australian Standards include: | AS/NZS 2455.1:2007 Textile floor coverings - Installation practice - General AS 1884-2012 Floor coverings - Resilient sheet and tiles - Installation practices |
Sources of power supply include: | electric gas petrol |
Attachments include: | cutting heads vacuum systems |
Fault reporting includes: | verbal or written reporting |
Fittings and fixtures include: | nails door stops gripper strips metal mouldings |
Personal protective equipment includes: | that prescribed under legislation, regulations and enterprise policies and practices |
Information and procedures include: | workplace procedures relating to the use of tools and equipment work instructions, including job sheets, cutting lists, plans, drawings and designs workplace procedures relating to reporting and communication manufacturer specifications and operational procedures |
Sectors
Flooring technology