NTISthis.com

Evidence Guide: MSFFF1001 - Complete a basic furniture finishing project

Student: __________________________________________________

Signature: _________________________________________________

Tips for gathering evidence to demonstrate your skills

The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!

From the Wiki University

 

MSFFF1001 - Complete a basic furniture finishing project

What evidence can you provide to prove your understanding of each of the following citeria?

Plan and prepare for work

  1. Work requirements are correctly identified from drawings, specifications and instructions
  2. Quality assurance requirements are recognised and adhered to in accordance with enterprise operation
  3. Work health and safety (WHS) requirements, including personal protection needs, are observed throughout the work
  4. Tools, equipment and materials selected are consistent with job requirements and work instructions, checked for safety and serviceability, and any faults reported to supervisor
Work requirements are correctly identified from drawings, specifications and instructions

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Quality assurance requirements are recognised and adhered to in accordance with enterprise operation

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Work health and safety (WHS) requirements, including personal protection needs, are observed throughout the work

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Tools, equipment and materials selected are consistent with job requirements and work instructions, checked for safety and serviceability, and any faults reported to supervisor

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Prepare surface and materials for finishing process

  1. Surfaces are checked for contamination and correct preparation according to workplace procedures and standards
  2. Products with surface or other faults are identified and faults are reported or repaired according to workplace procedures and standards
  3. Techniques for application of materials for finishing process are identified and used according to workplace procedures
  4. Materials suitable for basic surface finishing are prepared
Surfaces are checked for contamination and correct preparation according to workplace procedures and standards

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Products with surface or other faults are identified and faults are reported or repaired according to workplace procedures and standards

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Techniques for application of materials for finishing process are identified and used according to workplace procedures

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Materials suitable for basic surface finishing are prepared

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Colour is applied to timber surface

  1. Stain is applied to timber surfaces in accordance with manufacturer specifications and workplace procedures and standards
  2. Stained surface is sealed with polish using mop brush, blender or swooge
  3. Sealed surface is lightly sanded to make smooth
  4. Wood filler or sanding sealer are applied in accordance with manufacturer specifications and workplace procedures and standards
  5. Filled-in surface is sealed with oil varnish in accordance with manufacturer specifications and workplace procedures and standards
Stain is applied to timber surfaces in accordance with manufacturer specifications and workplace procedures and standards

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Stained surface is sealed with polish using mop brush, blender or swooge

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Sealed surface is lightly sanded to make smooth

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Wood filler or sanding sealer are applied in accordance with manufacturer specifications and workplace procedures and standards

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Filled-in surface is sealed with oil varnish in accordance with manufacturer specifications and workplace procedures and standards

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Sealed surface is lightly sanded to make smooth

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Finishing material is applied to surface

  1. Finishing material is applied in accordance with manufacturer specifications until required build is achieved
  2. Finishing material is cut back to remove surface defects and/or foreign material in accordance with workplace procedures and standards
  3. Surface is burnished with fine steel wool and lubricating oil to achieve even sheen
Finishing material is applied in accordance with manufacturer specifications until required build is achieved

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Finishing material is cut back to remove surface defects and/or foreign material in accordance with workplace procedures and standards

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Surface is burnished with fine steel wool and lubricating oil to achieve even sheen

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Clean up work area

  1. Workplace is cleared of debris and unused materials
  2. Wood filler and lubricating oil rags are disposed of safely having regard for spontaneous combustion
  3. Tools and equipment are cleaned, maintained and stored
Workplace is cleared of debris and unused materials

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Wood filler and lubricating oil rags are disposed of safely having regard for spontaneous combustion

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Tools and equipment are cleaned, maintained and stored

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Assessed

Teacher: ___________________________________ Date: _________

Signature: ________________________________________________

Comments:

 

 

 

 

 

 

 

 

Instructions to Assessors

Evidence Guide

Elements describe the essential outcomes.

Performance criteria describe the performance needed to demonstrate achievement of the element.

1

Plan and prepare for work

1.1

Work requirements are correctly identified from drawings, specifications and instructions

1.2

Quality assurance requirements are recognised and adhered to in accordance with enterprise operation

1.3

Work health and safety (WHS) requirements, including personal protection needs, are observed throughout the work

1.4

Tools, equipment and materials selected are consistent with job requirements and work instructions, checked for safety and serviceability, and any faults reported to supervisor

2

Prepare surface and materials for finishing process

2.1

Surfaces are checked for contamination and correct preparation according to workplace procedures and standards

2.2

Products with surface or other faults are identified and faults are reported or repaired according to workplace procedures and standards

2.3

Techniques for application of materials for finishing process are identified and used according to workplace procedures

2.4

Materials suitable for basic surface finishing are prepared

3

Colour is applied to timber surface

3.1

Stain is applied to timber surfaces in accordance with manufacturer specifications and workplace procedures and standards

3.2

Stained surface is sealed with polish using mop brush, blender or swooge

3.3

Sealed surface is lightly sanded to make smooth

3.4

Wood filler or sanding sealer are applied in accordance with manufacturer specifications and workplace procedures and standards

3.5

Filled-in surface is sealed with oil varnish in accordance with manufacturer specifications and workplace procedures and standards

3.6

Sealed surface is lightly sanded to make smooth

4

Finishing material is applied to surface

4.1

Finishing material is applied in accordance with manufacturer specifications until required build is achieved

4.2

Finishing material is cut back to remove surface defects and/or foreign material in accordance with workplace procedures and standards

4.3

Surface is burnished with fine steel wool and lubricating oil to achieve even sheen

5

Clean up work area

5.1

Workplace is cleared of debris and unused materials

5.2

Wood filler and lubricating oil rags are disposed of safely having regard for spontaneous combustion

5.3

Tools and equipment are cleaned, maintained and stored

Required Skills and Knowledge

Elements describe the essential outcomes.

Performance criteria describe the performance needed to demonstrate achievement of the element.

1

Plan and prepare for work

1.1

Work requirements are correctly identified from drawings, specifications and instructions

1.2

Quality assurance requirements are recognised and adhered to in accordance with enterprise operation

1.3

Work health and safety (WHS) requirements, including personal protection needs, are observed throughout the work

1.4

Tools, equipment and materials selected are consistent with job requirements and work instructions, checked for safety and serviceability, and any faults reported to supervisor

2

Prepare surface and materials for finishing process

2.1

Surfaces are checked for contamination and correct preparation according to workplace procedures and standards

2.2

Products with surface or other faults are identified and faults are reported or repaired according to workplace procedures and standards

2.3

Techniques for application of materials for finishing process are identified and used according to workplace procedures

2.4

Materials suitable for basic surface finishing are prepared

3

Colour is applied to timber surface

3.1

Stain is applied to timber surfaces in accordance with manufacturer specifications and workplace procedures and standards

3.2

Stained surface is sealed with polish using mop brush, blender or swooge

3.3

Sealed surface is lightly sanded to make smooth

3.4

Wood filler or sanding sealer are applied in accordance with manufacturer specifications and workplace procedures and standards

3.5

Filled-in surface is sealed with oil varnish in accordance with manufacturer specifications and workplace procedures and standards

3.6

Sealed surface is lightly sanded to make smooth

4

Finishing material is applied to surface

4.1

Finishing material is applied in accordance with manufacturer specifications until required build is achieved

4.2

Finishing material is cut back to remove surface defects and/or foreign material in accordance with workplace procedures and standards

4.3

Surface is burnished with fine steel wool and lubricating oil to achieve even sheen

5

Clean up work area

5.1

Workplace is cleared of debris and unused materials

5.2

Wood filler and lubricating oil rags are disposed of safely having regard for spontaneous combustion

5.3

Tools and equipment are cleaned, maintained and stored

Interpret work order and locate and apply relevant information

Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment

Identify materials used in the work process

Follow work instructions, operating procedures and inspection processes to:

minimise the risk of injury to self or others

prevent damage to goods, equipment and products

maintain required production output and product quality

Complete a basic furniture finishing project

Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements

Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures

Minimise wastage of resources, including materials, time and money

Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity

Characteristics, limitations and uses of coating materials required for the project

Coating application equipment, techniques and safe working procedures

Basic repair techniques to defects in timber surfaces

Safe handling of materials associated with applying coatings

Range Statement

Specifies different work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Range is restricted to essential operating conditions and any other variables essential to the work environment.

Unit context includes:

WHS requirements, including legislation, building codes, material safety management systems, hazardous and dangerous goods codes, and local safe operating procedures or equivalent

work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements

work requires individual to demonstrate some discretion, judgement and problem solving in the accurate application of polish

A basic project includes:

the coating of tables, chairs or stools and other furnishing items

Stains include:

water stain

pigment oil stain

lacquer-based wiping stain

Wood grain fillers include:

oil-based filler

polyurethane (plastic) filler

water-based filler

Finishing materials include:

oil varnish

marine varnish

lacquer and sanding sealer

Lubricating oils include:

linseed oil

paraffin oil

'teak' oil

Surface faults include:

machine marks

bruising

pencil marks

grease

cross-sanding marks

scratches

glue marks

dirt marks

insect and termite holes

holes

knots

and blisters

Tools and equipment include:

filler blades

brushes

spray equipment

sandpapers

skinning in

bodying up and spiriting out rubbers

mop brush

blender

swooge and scrapers

Personal protective equipment includes:

that prescribed under legislation, regulations and enterprise policies and practices

Information and procedures include:

workplace procedures relating to the use of tools and equipment

work instructions, including job sheets, cutting lists, plans, drawings and designs

workplace procedures relating to reporting and communication

manufacturer specifications and operational procedures