The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!
From the Wiki University
What evidence can you provide to prove your understanding of each of the following citeria?
Plan and prepare to assist coiled tubing
|
|
Obtain, interpret and confirm work requirements Completed |
Evidence:
|
Access, interpret and apply documentation required to assist coil tube drilling operations and confirm work activity is compliant Completed |
Evidence:
|
Identify and minimise environmental issues and potential hazards, and assess and address risks within scope of own role and according to workplace procedures Completed |
Evidence:
|
Select and wear personal protective equipment required for work activity Completed |
Evidence:
|
Communicate with other personnel at site according to work requirements and confirm briefings and handover details are communicated and received Completed |
Evidence:
|
Check, fit and replace restraining devices on all pressure hoses as required Completed |
Evidence:
|
Raise alarm and report as required Completed |
Evidence:
|
Assist storage reel installation
|
|
Position crane hook to centre of storage reel Completed |
Evidence:
|
Hoist the storage reel over the centre of the carrier and lower into saddles Completed |
Evidence:
|
Lock down storage reel with retainer brackets and set tension screws Completed |
Evidence:
|
Install circulating equipment Completed |
Evidence:
|
Assist storage reel removal
|
|
Remove mud tank side hoses, swivel and cross over Completed |
Evidence:
|
Line up saddles and cut excess coil tubing on rig floor with casing cutter Completed |
Evidence:
|
Align saddles to remove storage reel Completed |
Evidence:
|
Install dog nut and chain coil Completed |
Evidence:
|
Open level wind box, shut off motor and lockout rig and open storage reel saddles Completed |
Evidence:
|
Remove lockout and prepare to pick up coil Completed |
Evidence:
|
Measure amount of coil cut and record remaining length Completed |
Evidence:
|
Assist installation of tubing snake connector
|
|
Prepare coil tubing ends Completed |
Evidence:
|
Check the o-rings for die retention are not stretched out Completed |
Evidence:
|
Separate two-piece tubing snake connector in middle at the threads Completed |
Evidence:
|
Size, install and tighten threaded half of tubing snake connector into tail end of coil tubing on the storage reel Completed |
Evidence:
|
Size, install and tighten threaded half of tubing snake connector into tail end of coil tubing on the injector side Completed |
Evidence:
|
Align tubing connector up and screw two tubing stake connector pieces together at centre treads Completed |
Evidence:
|
Assist handling of tubing snake connector
|
|
Inspect derrick and rig floor for equipment Completed |
Evidence:
|
Monitor workplace and communicate with driller as required while conducting slip and cut of coil Completed |
Evidence:
|
Run coil with tubing snake connector and confirm safe distance of injector from iron roughneck and other objects Completed |
Evidence:
|
Assist installation of set screw tubing dimple
|
|
Prepare coil tubing end with a grinder Completed |
Evidence:
|
Install dimple template Completed |
Evidence:
|
Tighten all set screws on dimple template Completed |
Evidence:
|
Loosen screws and remove template Completed |
Evidence:
|
Deepen template indents with a drill to dimple screw depth Completed |
Evidence:
|
Inspect tubing dimple seals Completed |
Evidence:
|
Install dimple set screws Completed |
Evidence:
|
Assist bottom hole assembly operations
|
|
Place float on bit and install bit sub onto bit Completed |
Evidence:
|
Stab drill collar in bit sub and make up drill collar into bit sub Completed |
Evidence:
|
Pick up sub and position where needed for stabbing into stump Completed |
Evidence:
|
Guide driller stabbing the dimple into the bottom hole assembly on the stump and confirm dimple is lined up to prevent from cross threading Completed |
Evidence:
|
Apply make-up tong to dimple while making up bottom hole assembly Completed |
Evidence:
|
Apply breakout tong to dimple and make up tong to BHA and torque to specifications Completed |
Evidence:
|
Assist tripping in with coil tubing
|
|
Confirm the lube tube is down and air bag inflated on flow T Completed |
Evidence:
|
Confirm arch pin is retracted while tripping in and free movement of the arch Completed |
Evidence:
|
Grease and inspect injector as per industry standards Completed |
Evidence:
|
Assist tripping out with coil tubing
|
|
Verify level wind is lined up ready to trip out Completed |
Evidence:
|
Check the air bag on flow T is still inflated Completed |
Evidence:
|
Verify level wind continuously stays in with coil while tripping out Completed |
Evidence:
|
Assist lifting the lube tube when bottom hole assembly reaches 75 metres prior to pulling out of hole Completed |
Evidence:
|
Assist slipping and cutting of coil tubing-grinder/rod cutter
|
|
Place tubing dimple at the desired working height Completed |
Evidence:
|
Place the hole cover in position Completed |
Evidence:
|
Removing tubing dimple Completed |
Evidence:
|
Run coil tubing through table to acceptable height while taking precautions to reduce stress on coil Completed |
Evidence:
|
Cut coil tubing with grinder/rod cutter Completed |
Evidence:
|
Remove with double wrapping sling and wire line Completed |
Evidence:
|
Lay down through v door. Completed |
Evidence:
|
Measure length cut off to keep accurate length Completed |
Evidence:
|